3/18/2023 0 Comments Macminer moneroKnowing a bit about each of the mining software types we can dive into each of them in greater detail and explore the different options of software that exist. The pool and miners are able to communicate what work needs to be done and how the hashing needs to be used by the mining machines. This software is responsible for communication between mining pools and the ASIC firmware. Stratum V2 helps reduce mining centralization, protect miners from having hashrate stolen and improve communication between miners and mining pools. Stratum V1 has some shortcomings, but will be improved upon with Stratum V2. Stratum V1 is the most commonly used protocol by the majority of the mining pools. This protocol is the communication bridge between the Bitcoin network and the mining pool. This specialized tool is useful when managing multiple miners to help ensure that each mining device is running properly and efficiently. There are solutions that are solely used to understand the performance of your miner(s). You also have the option of using third-party firmwares that are provided by other companies. While this firmware is sufficient to mine Bitcoin, it is not always the best to use. When you buy a miner from the manufacturer it comes installed with their stock firmware. This is the code that is running on the actual device. To better understand the different types of Bitcoin Mining Software we will break these into several different categories: The software is used to manage your miner(s) and to optimize their performance. Bitcoin mining software controls the way this equipment runs, and interfaces with Bitcoin and the different mining pools. Where Bitcoin mining hardware is the equipment needed to mine Bitcoin. Now that you know the best Bitcoin mining hardware, we’re going to talk about Bitcoin mining software. If you are experiencing problems with devices not activating when you start mining, this is an essential troubleshooting step.Learn more about our editorial guidelines Updated September 14, 2022 Once you know where your device is and what it's called, you can enter -S /dev/cu.MYDEVICE in the custom flags field of the miner settings rather than -S all. If you have installed the drivers for your device and, enter ls -l /dev/cu.* instead and the list will be much shorter, and likely the only non mining devices will be labelled as modems. If you have not installed the drivers for your device, enter ls -l /dev/* and your device(s) will show up and hopefully stand out from the long list it prints. Open the Terminal in your Utilities folder. On Mac OS 10.9 the native usb serial driver prevents cgminer from accessing devices and bfgminer in the FPGA/ASIC window is recommended, but if you attempt to start mining in cgminer window on 10.9 instructions on temporarily disabling the system driver will be revealed. If you have not installed the drivers for your device and are running any version of Mac OS X prior to 10.9, cgminer should autodetect them when you press start without any other setup. In earlier versions you must specify the devices individually, this is still possible in later versions. Check the logs and you should see your devices being activated just after you start. If you make any changes click apply, and start the miner. ![]() This is what the buttons that are there for each device actually does. S bigpic:all -S antminer:all -S erupter:all -S bfl:all Using MacMiner 1.4.6 or higher plug your device(s) in (After installing the drivers they require - BFL drivers Block Erupter/Antminer Drivers) and go to miner settings, you can try entering -S all in the custom flags field but this sometimes prevents bfgminer from working, so each device category should be activated like so: bfgminer and cgminer cannot access the same devices with the same driver setup. ![]() Users of earlier versions of Mac OS than 10.9 should use cgminer, unless they've installed the specific usb serial driver for their device. Users running 10.9 Mavericks (a free, recommended upgrade) should use the FPGA/ASIC window as this will work without removing any system drivers. Getting started with your FPGA/ASIC deviceĭue to issues with drivers, which miner to use is best decided by your version of Mac OS X. FabulousPanda's MacMiner Setting up an FPGA or ASIC device
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |